Nouveau Upa-usb V1.3 avec tous les adapteurs. L'appareil principal peut être relié directement à la Elrasoft.com UUSP (UPA-USB série de programmeur) ou par un DB9 mâle / femelle en option 1:1 câble d'extension. Il est équipé d'une prise 40pin ZIF pour tous les appareils DIP / DIL étroites et larges ainsi qu'avec un SOIC ZIF (150mil, étroit) prise 16 pin pour couvrir les dispositifs les plus couramment utilisés. Configuration de l'appareil se fait par touches de configuration spéciales qui rendent le travail pratique et sûre par rapport au câblage jusqu'à tout manuellement.
UPA USB 2015 V1.3.0.14 With Full Adaptors
Supported language: English
XPROG-M V5.60 XPROG M Programmeur avec USB Dongle est la seule version que XPROG-M peut déchiffrer la nouvelle version de BMW CAS4. Pas de limitation du système d'exploitation, un logiciel peut être installé sous Windows XP, Windows 7. Ajouter une nouvelle autorisation: AUTH-0025 Authorized 11/4/2014.
Xprog-m V5.3 XPROG M Programmeur Plus Avec Dongle
Xprog box latest version 5.84 comes with new authorization - AUTH-0028-1 Renesas V850 and AUTH-0028-2 Renesas SuperH
This CMD CAN Flasher V1251 read and write flash memory via the diagnostic connector on the CAN line of computers with motor MED9.1, MED9.5, EDC16U3x/CP, EDC16CP31, EDC16CP36, EDC16C3 and EDC16C9 fuel injection. Working through CAN, not on K line.
KTM ECU chip Tuning can read the chip data, read & write ECU data, read transmission data etc at a high speed.
L'outil de réglage de la puce ECU100 ECU est un lecteur / programmeur universel (il ne nécessite pas nécessairement notre logiciel RACE) qui permet à l'utilisateur de lire et de programmer des fichiers dans l'ECU fourni avec le processeur MOTOROLA MPC5xx (indispensable).
X-PROG Box ECU Programmer XPROG M V5.5 Support CAS4 5M48H Nouvelle Version
CARPROG est un outil universel pour les auto radios, odomètres, tableaux de bord, réparation d’antidémarrage ayant les fonctions suivantes: EEPROM et programmateur de microcontrôleur, programmateur de transpondeur de clé.
MPPS V21 Français MAIN + TRICORE + MULTIBOOT avec Breakout Tricore Câble
Dernière Software version: V21
MPPS Chiptuning Flasher supports new EDC16, EDC17, MED9.x, Siemens PPD1/x, EDC15, ME7.x and many other... Professionaly made, no obsolete boxes of cables, all the electronics fits the OBD plug.
Version:V13
New UPA USB Programmer Main Unit
Software version: V1.3
KTM ECU chip Tuning can read the chip data, read & write ECU data, read transmission data etc at a high speed. Full Set Adapters for KTM ECU chip Tuning Car ECU Programmer, make your job easier.
Unité centrale de Carprog Full, ne contient pas de câbles.
Si votre carprog unité est en panne, nous pouvons acheter un nouveau à remplacer.
V5.48 X-PROG Box ECU Programmer XPROG M.
The XPROG box project is a continuation of the project XPROG and now supports more than 450 units (serial EEPROM`s, Microcontrollers (MCU), Electronics Control Units (ECU), DashBoards, Immobilizers, Calculators and others).
The WELLON Programmers are affordable, reliable, and fast universal device programmers. They are
designed to operate with the Intel Pentium-based IBM-compatible desktop computers and laptops. No
interface card is necessary to plug the module into a PC (this feature is especially handy for laptop users).
The menu-driven software interface makes them easy to operate.
Firmware V8.21 CARPROG avec 21 adapteurs comprend beaucoup plus de autorisations que version V4.74 ou autres ancienne version CARPROG. V8.21 logiciel faut activer, mais vous obtiendrez automatiquement jeton renouveler après épuisé.
Audi VW micronas /Fujitsu programmer 2.0 > R200+R250
Audi VW micronas/Fujitsu programmer 2.0 replace the R200 and R250 fully
UPA USB Serial Programmer was used to do motorola chip programming.It's similar with XPROG-M programmer.