[Août Promo] KTM ECU chip Tuning ECU Programmer & Transmission Power Upgrade Tool Support 271 MSV80 MSV90

Numéro d'article.SE140 En rupture de stock. Histoire 29 vendu.

Achat immédiat: 222
Poids:
0.6KG
Paquet:
28.5cm*18cm*7cm ( Inch: 11.19*7.07*2.75 )
Résultats:
Retour de remboursement dans 7 jours, l'acheteur paie les frais de retour. Lire les Détails »

Description du produit

KTM ECU chip Tuning can read the chip data, read & write ECU data, read transmission data etc at a high speed.
KTM  ECU Programmer & transmission power upgrade tool Support 271 MSV80 MSV90
Software Version: V141
USBKey Version: 1.94

SE140-T Full Set Adapters

Read the chip data, read & write ECU data, read transmission data etc at a high speed.

KTMECU chip Tuning Functions:
1.Read the Chinese car via OBD.
3.Read the BOOT mode according to the chip model
4.Read the encrypted ECU password (Read the password of encrypted ECU first, then read data)
5. Support cars made in China with ME17 TC1728/1767 for data reading & writting and password reading.
 
Workable Transmission Model:
VAG: DQ200 (0AM) 
VAG: DQ200MQB/G2 (0CW) 
VAG: DQ250C (02E) K-Line 
VAG: DQ250E/F (02E) 
VAG: DQ250MQB (0D9) 
VAG: VL300/V30 (01J/0AN) K-Line 
VAG: VL300/V30 (01J/0AN)
VAG: VL381 (0AW) 
VAG: DQ500 (0BH/0BT) 
VAG: DL501/G2 (0B5) 
VAG: DQ200/MQB Boot (MICRO) 
VAG: DQ200/MQB Boot (EEPROM) 
VAG: DQ200G2 Boot (MICRO) 
VAG: DQ200G2 Boot (EEPROM) 
VAG: DQ250E/F/MQB Boot (MICRO) 
VAG: DQ250E/F/MQB Boot (EEPROM) 
VAG: VL300/V30 BSL (ECU chip Tuning)
VAG: VL300/V30 BSL (EEPROM) 
VAG: VL381 Boot (MICRO) 
VAG: VL381 Boot (EEPROM) 
VAG: DL501 Boot (MICRO) 
VAG: DL501 Boot (EEPROM)
VAG: DL501G2 Boot (MICRO) 
VAG: DL501G2 Boot (EEPROM)
 
Read Chinese car via OBD:
China: Chery, Great Wall, Lifan, SAIC ME17 (ME17.8.8) 
China: Chery, Great Wall, Lifan MT80 K-Line Calibration (Delphi MT80)
China: Chery, Great Wall, Lifan MT80 CAN-bus (Delphi MT80)
 
Read the BOOT mode according to the chip model:
Infineon: TC1762/TC1766 MICRO (1504KB) 
Infineon: TC1762/TC1766 EEPROM (32KB) 
Infineon: TC1792/TC1796 MICRO (2048KB) 
Infineon: TC1796 MICRO+EXT (4096KB/6144KB) 
Infineon: TC1796 EXT (2048KB/4096KB) 
Infineon: TC1796 EEPROM (128KB) 
Infineon: TC1792 EEPROM (64KB) 
Infineon: TC1738/TC1767 MICRO (2048KB)
Infineon: TC1738/TC1767 EEPROM (64KB) 
Infineon: TC1797 MICRO (4096KB) 
Infineon: TC1797 MICRO+EXT (6144KB/8192KB)
Infineon: TC1797 EXT (2048KB/4096KB) 
Infineon: TC1797 EEPROM (64KB) 
Infineon: TC1724/TC1728 MICRO (1536KB)
Infineon: TC1724/TC1728 EEPROM (64KB) 
Infineon: TC1782/TC1784 MICRO (2560KB) 
Infineon: TC1782/TC1784 EEPROM (128KB) 
Infineon: TC1793/TC1798 MICRO (4096KB) 
Infineon: TC1793/TC1798 MICRO+EXT (6144KB/8192KB) 
Infineon: TC1793/TC1798 EXT (2048KB/4096KB) 
Infineon: TC1793/TC1798 EEPROM (192KB) 
 
Read the encrypted ECU password (Read the password of encrypted ECU first, then read data):
Bosch: Support Chinese car ME17 TC1728/1767 data reading & writing and password reading
Bosch: BMW/MB/VAG GPT 
Bosch: Ford/Opel/Volvo GPT 
Bosch: BMW TPROT8+ 
Bosch: VAG TPROT8+ 
Bosch: Kia/Hyundai/Honda TPROT8+ 
Bosch: Chrysler/Jeep/Dodge/Fiat TPROT8+ [Test] 
Bosch: VAZ/UAZ ME17.9.71  
Continental: Kia/Hyundai/SsangYong SIM2K-24X/C201 
Continental: Ford EMS2204
Continental: Ford EMS2207 
Continental: Ford EMS2211
Continental: Ford SID208 
Continental: Ford SID209 
Continental: Ford Mondeo 4 SID807EVO
Continental: Ford Focus 3/Transit Connect SID807EVO 
Continental: Citroen/Peugeot SID208 
Kia/Hyundai: Delphi MT86 EEPROM (16KB) 
Mercedes-Benz: Delphi CRD3.1 EEPROM (32KB) 

How to use KTM ECU chip Tuning ECU programmer Switch board? 
 
1. The switch board is designed to work with J2534, this device uses the Ktag cables so the user can refer to the Ktag wiring diagram. 
 
2. Advise you use Open Port2.0 as the protocol conversion equipment and work with PC.
 
3. There are 3 types of Bosch Infineon ECU : 
 1) The Infineon ECU before TPROT8.
 2) TPROT8-10 
 3) The Infineon ECU after TPROT10 which is what we call GPT encrypted. 
 
4. The Infineon ECU before TPROT8 is not encrypted, you directly uses the BOOT point 
grounding, then follow the Ktag user manual to wire the cable and read the data. 
 
5.For TPROT8-10,the Bosch Company set the anti-debugging mode, reading EEPROM needs no password and reading ECU chip Tuning needs password. 
 Therefore, during the reading process, there is an extra CNF1, Boot outputs low level and CNF1 outputs high level. When reading, Boot needs to add one small resistor and ground it. CNF1 to connect one 470ohm-2K resistance, then connect 3.3V, it's very important, otherwise the ECU will be burnout. 
2 tips on reading the data: 
 1) BOOT and CNF1 must be connected when reading data. 
 2) Only connect BOOT not CNF1 When reading the password, otherwise the password can't be read out. Also you can follow the Ktag wiring diagram because Ktag controls the CNF1 turn on and off, so it can't be disconnected. When reading the password, you turn the two switches to the automatic mode, and to the On mode when reading the data, when the software prompts, you choose " Manually" then follow the message to turn on or off.
 
6. For GPT encrypted ECU, the S1, S2 and Boot cable are needed to connected when reading password, and the S1, S2 don't need to be connected when reading data.

Package includes:
 
1pc x KTMECU chip Tuning ECU Programmer
1pc x KTMECU chip Tuning USB Dongle


Colis sera envoyé à l'adresse enregistrée sur paypal uniquement

Contactez-Nous:

Email:
sales@obd2diy.fr
Skype: diyobd.fr
Whatsapp: +86 17308368390

Facebook
https://www.facebook.com/obd2diy2011/

Quel est le sens de QC marque sur produit?

1. Le QC marque signifie que ce produit a passé letest de notre ingenieur.
2. Le QC marque signifie que le produit est de notre société.
3. Le QC marque signifie que le produit obtiendra la garantie.

Vidéos

Service technique

KTM flash ECU Programmer Notice:

1. vous ne pouvez qu'utiliser notre logiciel
2. Il ne faut pas avoir logiciel comme ECU flash installé dans l'ordinateur. Si l'ordinateur déjà installer ce logiciel similaire, il faut changer un autre ordi ou reinstaller le windows système, et puis installer notre logiciel en suivant la vidéo. Sinon, interface sera bloqué.  Il est mieux que deconnecter le réseau.
3. Il y a logiciel et vidéo de test sur notre dvd, il peut vous aider.
4. KTM flash peut lire Infineon ecu et gearbox(transmission) ecu.
5.  Quand on lit  Infineon chiffré ou ecu chiffré, il faut lire d'abord le fichier mot de passe, nous avons la vidéo pour montrer. Si le logiciel affiche qu'éteindre l'alimentation pendant 2 secondes, il faut le faire nécessaire. Après 2 secondes, continuez le.

vidéo KTM flash Install Read TC1797
Pièces et accessoires optionnels
Les clients ayant consulté cet article ont également consulté